Fun light project
This project demonstrates a basic understanding of soldering various electronic components such as LEd's, resistors, capacitors, IC chips, and wires. When completed the board creates various LED patterns at various speeds
Conclusion questions.
1.
Solder is an alloy of what two metals?
Solder is an alloy of tin and copper.
2. What is tinning, and why is it important to keep the tip of your soldering iron tinned?
Tinning is the process of applying solder to the tip of your soldering iron to prevent oxidation and allow your soldering iron to conduct heat better.
3. The six most common mistakes made while soldering are overheating the component, using too much solder, moving the solder while the component is drying, creating cold joints, using to little solder, and creating solder bridges.
4. You can desolder a component using a soldering iron and a solder suceker or by using a hot solder wick.
5. The solder used in electronics is commonly 60/40 solder because it has a low melting point and is stickey enough to connect the small parts.
6. A cold solder joint is a solder joint that has no sufficient connection between components.
7. The melting point of 60/40 solder is between 190 and 840 degrees fahrenheit.
8. The typical wattage of an electronics soldering iron is 70 watts.
Solder is an alloy of tin and copper.
2. What is tinning, and why is it important to keep the tip of your soldering iron tinned?
Tinning is the process of applying solder to the tip of your soldering iron to prevent oxidation and allow your soldering iron to conduct heat better.
3. The six most common mistakes made while soldering are overheating the component, using too much solder, moving the solder while the component is drying, creating cold joints, using to little solder, and creating solder bridges.
4. You can desolder a component using a soldering iron and a solder suceker or by using a hot solder wick.
5. The solder used in electronics is commonly 60/40 solder because it has a low melting point and is stickey enough to connect the small parts.
6. A cold solder joint is a solder joint that has no sufficient connection between components.
7. The melting point of 60/40 solder is between 190 and 840 degrees fahrenheit.
8. The typical wattage of an electronics soldering iron is 70 watts.
Game board counter.
This project uses basics soldering skills and multiple components to generate random numbers in random patterns.
Conclusion
The number one was spun a total of 8 out of 29 times with a distribution of 27%.
The number two was spun a total of 3 out of 29 times with a distribution of 3%.
The number three was spun a total of 4 out of 29 times with a distribution of 13%.
The number four was spun a total of 4 out of 29 times with a distribution of 13%.
The number five was spun a total of 3 out of 29 times with a distribution of 3%.
The number six was spun a total of 7 out of 29 times with a distribution of 24%.
1. My numbers ranged from 3% to 27% distribution. i think its fair it distributes numbers at random which isnt always even for each number.
2. Admiral grace hoope coined the term bug and debug.
The number two was spun a total of 3 out of 29 times with a distribution of 3%.
The number three was spun a total of 4 out of 29 times with a distribution of 13%.
The number four was spun a total of 4 out of 29 times with a distribution of 13%.
The number five was spun a total of 3 out of 29 times with a distribution of 3%.
The number six was spun a total of 7 out of 29 times with a distribution of 24%.
1. My numbers ranged from 3% to 27% distribution. i think its fair it distributes numbers at random which isnt always even for each number.
2. Admiral grace hoope coined the term bug and debug.